a Grand Re-Opening???

Ok, I took a year off from selling on MyFountainDesigns- ok – a year and a half! But am thinking about opening her back up. I mentioned earlier on my main blog – http://MountainHigh.wordpress.com – about selling the domain name- MyFountainDesigns.com , but I just didn’t/couldn’t do it! I have alot of blood, sweat and definitely tears in that biz 🙂 so I just kept it. Its mine, soooo- IF the value of the U.S. dollar EVER goes back up [when obama goes OUT] I WILL open back up! So then all Mist Fountain, Waterfall Fountains, Negative Ion Generators, and deco Cool Mist Humidifier lovers will be able to get the BEST Fountain Parts, always at the lowest prices on the web, once again.

Now, don’t that make you smile? 🙂


How To Make a Mist Fountain


For the basics you will need
* A bowl of your choice
* A Drill to make hole in your bowl [not a ‘must have’ – see below]
* a Glass/ceramic specialty drill bit [only IF you want a hole in your fountain bowl]
* a mistmaker
* AC Adapter power Transformer
* a center stand and a Lid -to prevent splashing.
* you can use a metal center stand or a plastic ‘splashguard’ [to set inside the fountains bowl to hold the mist maker, and the lid sits on top]

*Drill a hole in the side of your container, near bottom, with a diamond cut bit. The hole must be the same diameter as the Mist Unit cord so buy drill bit accordingly.-*see note below

**a hole is NOT an absolute must. Save time, money, and work! Don’t drill a hole. Let the cord drape over the side of the bowl/container/pot, like the one I made shown below. You can slide the plug [on mist maker unit cord] further down the cord so it won’t show.

Create an indoor fountain

Create a Mist fountain

 An Indoor Fountain Creation

My First Misting Fountain Design


* Put the Mist Maker Unit in your bowl
* IF you made a hole, put the mist maker cord thru it. Push the plug on the cord through the hole [wet the plug to make it easier]
* Put center stand or splashguard in fountain bowl
* set mist unit in bottom of center stand
* put the small matching Lid on top of the center stand
* Fill your bowl with clean water to ABOVE the sensor`on mist unit
* Connect the mist maker unit to the a/c adapter and plug into the wall.

Enjoy your Custom Misting Fountain Design that YOU made yourself!

A good mist maker unit has a water level sensor. It may have an upside down “U” or a ’round ball’, or a ‘stick with a tiny ball on the end of it, that’s the water level sensor. Keep the water level ABOVE the sensor.



Do you hang flowers outside in the summer? BIG FLOWERPOTS? and have you ever used a ROD IRON HANGING Bracket? Good. You can use one of those ROD IRON brackets to mount a Wall Misting Fountain from any chosen spot. You need:

– ROD IRON bracket [or something to hang your fountain on] and you can customize your hanging fountain bracket too! all you need is imagination
– Hanging Flower basket, the sturdier the better. OOOOORRRAA. IF you can find a hanging assembly for a hanging mist fountain, USE IT! but unfortunately, I aka MountainHigh,
am all sold out
– mist maker unit w/ac adapter

– splashguard
– lid

If using a Rod Iron bracket, [get one at any dept store or hardware] decide where you want your fountain to hang, and SECURELY mount the bracket with the screws included.

– Place the Hanging Assembly on a flat surface
– set a proper size bowl in the center – it doesn’t have to be the exact shape of the hanging pot
– Use the Chain, and hook each loop on the holder, to the 3 ends of the chains
– Carefully pick up the end of the chains that come together at the top end and lift the bowl and Hanging Basket.
– Hang the Hanging Basket from the Rod Iron Bracket or your pre-chosen place
– put the mist unit and splashguard in the bowl, add water, put lid on top of splashguard, wind the mist unit cord up and around one of the chains or the bracket, hook the a/c adapter to the mist unit, and enjoy


Add a WATERFALL EFFECT with an underwater pump – with mine, I have a pump and 2 mistmaker units going in the 18″ metal bowl

How to build, design, make a Mist Fountain or waterfall, with fountain replacement parts like: splash guards, lids, floor and tabletop fountain stands and fountain bowls.
Learn how to make a wall fountain.

Make your own Indoor Waterfall Fountain with a large round bowl, or a Lotus Bowl and an underwater waterfall pump. As of 2/22/2011  I still have some of these parts- small bowls, 16mm replacement discs, underwater pumps [for small bodies of water like a fountain] and mist fountain a/c adapters. Contact me here if you wish to inquire about any of these items.

Fragrance Oils in Mist Fountains

Use Lightweight Oils ONLY

I do not recommend using Fragrance Oils in Misting Fountains because they clog the ceramic disc. It is the ceramic disc that creates the mist. But,  if you do use Fragrance Oils or ‘ Scented Oils’  in your mist  fountain, use ONLY Quality Lightweight Oils

You must change the water, clean your fountain bowl, mist unit, and replacement disc more often when using oils in your fountain.
If you choose to use Fragrance Oils, select Quality oils, like ours.

Use ONLY a couple drops oil for each CLEAN BOWL of water. That is not the same as a couple drops every time you add water to your fountain bowl. You will clog your mist unit and/or ceramic disc with too much oil per bowl of clean water. So dump the water out everyday and then add oil. Better yet, dump the water out, use a Q-Tip and gently cleanse the Mist Maker and Ceramic Disc everyday to get all oil buildup off the parts. If you have a Tabletop Fountain, it will be very easy to do this, a bit more work with a floor fountain.

Even better…. to fill your home with the delightful fragrance of your favorite Fragrance Oil, use one of our Electric Oil Warmers! No Flame! No Soot! No Candles!

Real Essential Oils can be added as desired


YOU MUST Keep the water and Mist Fountain Bowl clean to keep your mist fountain in good misting condition


how to clean mist fountain parts


Everyone’s home environment is different, so adjust your cleaning times accordingly.
The easiest way to clean your fountain bowl is in your dish water.

– Run soapy water in sink
– unplug adapter from the wall and mist unit
– You may want to dip some water out of the bowl before lifting the bowl out of the fountain stand
– Carefully pick your bowl up and out of the fountain stand and carry to the sink.
– Dump the dirty water out
– put your bowl and mist unit in clean dish water – keep end of cord out of water!
– wash it – use cotton swabs for mist unit and disc
– dry with soft cloth
– put fountain back together
– add clean water to bowl.



It’s easy to keep mist fountain parts clean and trouble free with a little time and effort.

-Wet a cotton swab with gentle soap and water.how to clean mist fountain parts
-GENTLY clean around each of the LED lights that are around the outer edge of the Mist Maker Unit.
– Clean the ceramic disc while you are at it
– also GENTLY with soapy cotton swab

– You can put the mist maker in a bowl of soapy water to clean it. BUT BE CAREFUL! I’ve broke one of the LED lights off when cleaning the mist unit. I really wanted to get it clean! But I used that mist unit and the same disc for at least 6 more months, everyday!


How to clean Misting Ceramic Discs

How to clean your Ceramic Replacement Disc [or disk] with or without a keytool

the oils from your fingertips can ruin your replacement disc, a new disc or old one. The DISC is what makes the mist!

Our replacement ceramic discs come with a black rubber protective washer around the disc. Place a soft paper towel between your fingers and the new disk to remove the protective black rubber. …let the towel be between your fingers and disc at all times. The solid white side goes facing UP toward you, after it is placed in your mist maker.

Best way to clean the ceramic disc in your fountain’s mist maker
take it out of the mist unit IF you have a key tool. [see below]
Clean your disc as follows if you are having problems with your fountain’s mist maker OR in extreme cases of neglect to your mist maker – as in….. the disc is really cruddy!


A keytool comes with all new replacement Discs [ if a keytool doesn’t come with the disk, then DON’T buy it!].
– DO NOT touch the disc with your bare hands!
– Take the replacement disc out of the mist unit carefully using the key tool
– Place the disc on a soft lint free cloth, or a VIVA paper towel – so you won’t touch it.
– Wet a cotton swab or soft cloth with gentle soap and water and clean both sides of the disc.
– Take the disc out occasionally to clean it IF you have a key tool for that purpose
– clean the top of the disc regularly [see below]
– Completely dry the ceramic disc before putting back into mist unit.
– DO NOT try to take the disc out with anything but the key tool


– Wet a cotton swab with gentle soap and water
– GENTLY clean the top of the disc.
– Do Not touch the top of the replacement disc with anything else, especially your fingertips
– the oil from your fingertips can damage the disc…then it will not mist.

The easiest way to clean your mist maker and ceramic disc….. dump the water out of the fountain bowl, remove the mistmaker from the fountain bowl, place the mist maker in a bowl of clean soapy water and clean it with a cotton swap OR stick it in your dish water! [do not let the electrical connections to get wet!]

Clean the disc weekly if used daily for best results.

How to Remove White Rings in Mist Fountain Bowls

Do you have a white ring  around the inside of your Mist Fountain bowl?  That white ring is caused by Mineral Deposits In Your Water.
Clean it off like this…..
– Use white Vinegar to remove any rings or stains from your mist fountain bowl caused by mineral deposits. Take a clean cloth and place it over the top of a bottle of white vinegar. Now turn the bottle upside down to get the cloth wet with vinegar. Use that vinegar soaked cloth and wipe the white ring off your fountain bowl. It is simple and efficient.

DO NOT USE DISTILLED WATER IN YOUR FOUNTAIN! Your fountain needs some minerals in the water to make it function correctly
I personally use regular tap water, -aka city water- in my fountains.
IF you have very hard water, use Bottled Water but NOT Distilled water. If you do have hard water but filter it before using, it’s ok to use in your mist fountain too-unless it’s extremely hard water!